Exactly How To Install A Tub (For Beginners).
Exactly How To Install A Tub (For Beginners).
Blog Article
This article which follows on the subject of A Step-by-Step Guide to Installing a Bathtub is unquestionably enlightening. Don't miss it.
Mounting a bathtub isn't precisely brain surgery, yet it does require strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old bath tub with a new one is additionally a moderately challenging task. If the old bathtub is conveniently accessible, the job can relocate easily; if you have to open a wall surface to get rid of the old bathtub and position the brand-new bath tub, the task is much harder. In either situation, the job is within a residence handyman's skills, although you will need a helper to leave the old bathtub and also set in the brand-new one. See to it you have qualified yourself for the task as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed job, it is better to consider employing one before you begin. Chances are you may need a professional plumber to make tube connections.
This short article will help you set up a new tub in your restroom if you have already gotten a brand-new bathtub as well as do not need to alter the plan of your previous water system pipelines.
Your tools as well as material checklist ought to make up the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the supply of water. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic as a result of the limited gain access to that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end provides a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washers remain in place in between the faucet as well as the sink. Safeguard the tap in position with the supplier offered backnut. As soon as the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The previous type ought to be attached to the tap ends initially, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bathtub
Making use of the two wood boards under its feet, place the bathtub in the needed placement. The wooden boards are valuable in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four small points.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bathtub up until the spirit level checks out degree.
To mount taps, fit the bottom of the outermost adaptable faucet connector to the proper supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the supply of water as well as examine all joints and brand-new pipework for leakages and also tighten them if necessary. Fill the bathtub and also inspect the overflow electrical outlet and also the regular outlet for leaks.
Finally, fix the bath paneling as defined in the supplier's user's manual. Tiling and also securing around the bath tub needs to wait till the bath tub has actually been made use of at the very least when as this will certainly resolve it right into its last position.
Preparing for the Installation
Firstly, the supporting frame provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps device to stop stress on the bath tub.
Fit the adaptable faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you use every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its last setting.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a stiff seal, causing the water to pass through the wall surface in between the bath as well as the tiling, leading to difficulties with dampness and also possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and fittings. They are sold in tubes as well as cartridges, and can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water prior to securing, to enable the activity experienced when the tub remains in usage. The sealant can split fairly early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading up on Installing A Bathtub? Create feedback directly below. We will be interested to see your thinking about this blog entry. We are looking forward that you visit us again in the near future. Don't hesitate to take the time to promote this content if you appreciated it. Thanks a bunch for your time. Don't hesitate to pay a visit to our site back soon.
Schedule Service Report this page